Упътване до адрес:
Предложен маршрут:  

Още оферти

Описание
HPE Aruba Instant 215
JL186A
Affordable, high-performance 802.11ac

Multifunctional and affordable Aruba Instant 215 wireless access points (APs) maximize mobile device performance in medium-density, high-performance Wi-Fi environments.

UNIQUE BENEFITS

Wi-Fi client optimization
-IAP-215 features patented ClientMatch technology to eliminate sticky client behavior while users roam. ClientMatch continuously gathers session performance metrics from mobile devices.
-If a mobile device moves away from an AP or if RF interference impedes performance, ClientMatch automatically steers the device to a better AP.

Advanced Cellular Coexistence (ACC)-ACC lets WLANs to perform at peak efficiency by minimizing interference from 3G/4G LTE networks, distributed antenna systems and commercial small cell/femtocell equipment.

Quality of service for unified communication apps-IAP-215 supports priority handling and policy enforcement for unified communication apps, including Microsoft Lync with encrypted videoconferencing, voice, chat and desktop sharing.

A single AP automatically distributes the network configuration to other Instant APs in the WLAN. Simply power-up one Instant AP, configure it over the air, and plug in the other APs the entire process takes about five minutes.

TECHNICAL SPECIFICATIONS
2.4-GHz (450 Mbps max rate) and 5-GHz (1.3 Gbps max rate) radios, each with 3x3 MIMO and six integrated omni-directional downtilt antennas.

OPERATING MODES
Aruba Instant AP
Air monitor (AM) for wireless IDS, rogue detection and containment
Spectrum analyzer, dedicated or hybrid
Secure enterprise mesh

WIRELESS RADIO SPECIFICATIONS
AP type: Indoor, dual radio, 5 GHz 802.11ac and 2.4 GHz 802.11n 3x3:3
Software-configurable dual radio supports 5 GHz (Radio 0) and 2.4 GHz (Radio 1)
3x3 MIMO with three spatial streams and up to 1.3 Gbps wireless data rate
Support for up to 255 associated client devices per radio, and up to 16 BSSIDs per radio
Supported frequency bands (country-specific restrictions apply):
-2.4000 GHz to 2.4835 GHz
-5.150 GHz to 5.250 GHz
-5.250 GHz to 5.350GHz
-5.470 GHz to 5.725GHz
-5.725 GHz to 5.850GHz
Available channels: Dependent on configured regulatory domain
Dynamic frequency selection (DFS) optimizes the use of available RF spectrum
Supported radio technologies:
-802.11b: Direct-sequence spread-spectrum (DSSS)
-802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
Supported modulation types:
-802.11b: BPSK, QPSK, CCK-802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
Transmit power: Configurable in increments of 0.5 dBm
Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements):
-2.4-GHz band: +23 dBm (18 dBm per chain)
-5-GHz band: +23 dBm (18 dBm per chain)
Advanced Cellular Coexistence (ACC) minimizes interference from cellular networks
Maximum ratio combining (MRC) for improved receiver performance
Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance
Short guard interval for 20-MHz, 40-MHz and 80-MHz channels
Space-time block coding (STBC) for increased range and improved reception
Low-density parity check (LDPC) for high-efficiency error correction and increased throughput
Transmit beamforming (TxBF) for increased signal reliability and range
Supported data rates (Mbps):
-802.11b: 1, 2, 5.5, 11
-802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
-802.11n: 6.5 to 450 (MCS0 to MCS23)
-802.11ac: 6.5 to 1,300 (MCS0 to MCS9, NSS = 1 to 3)
802.11n high-throughput (HT) support: HT 20/40
802.11ac very high throughput (VHT) support: VHT 20/40/80
802.11n/ac packet aggregation: A-MPDU, A-MSDU

ANTENNAS
Six integrated downtilt omni-directional antennas for 3x3 MIMO with maximum antenna gain of 5.0 dBi in 2.4 GHz and 5.0 dBi in 5 GHz. Built-in antennas are optimized for horizontal ceiling mounted orientation of the AP. The downtilt angle for maximum gain is roughly 30 degrees.

OTHER INTERFACES
One 10/100/1000BASE-T Ethernet network interface (RJ-45)
-Auto-sensing link speed and MDI/MDX-802.3az Energy Efficient Ethernet (EEE)
-PoE-PD: 48 Vdc (nominal) 802.3af or 802.3at PoE
DC power interface, accepts 1.7/4.0-mm center-positive circular plug with 9.5-mm length
USB 2.0 host interface (Type A connector)
Visual indicators (LEDs):
-Power/system status
-Ethernet link status (ENET)
-Radio status (two; RAD0, RAD1)
Reset button: factory reset (during device power-up)
Serial console interface (RJ-45)
Kensington security slot

POWER
Maximum (worst-case) power consumption: 14.9 watts (PoE) or 13.6 watts (DC)
-Excludes power consumed by external USB device (and internal overhead); this could add up to 6 watts (PoE) or 5.5 watts (DC) for 5W/1A USB device
Maximum (worst-case) power consumption in idle mode: 8.2 watts (PoE) or 7.4 watts (DC)
Direct DC source: 12 Vdc nominal, +/- 5%
Power over Ethernet: 48 Vdc (nominal) 802.3af/802.3at compliant source
-USB port is disabled when using an 802.3af PoE power source; for unrestricted operation with PoE power, use an 802.3at compliant source
Power sources sold separately
When both power sources are available, DC power takes priority

MTBF: 538,975 hours (61.5 years) at +25 C operating temperature

180 mm x 180 mm x 45 mm (W x D x H)
610 g Продукт известен още и като JL 186 A, JL 186A, JL186 A
Мнения
Задайте въпрос

Данните и цените за продуктите предлагани от нашите партньори служат за напътствие и обща информация. Моля, преди покупка проверете дали съответстват на публикуваните данни от сайта на магазина или производителя. За евентуалните неточности и грешки не носим отговорност.

^